Sprinklers are an essential part of any landscaping project. They save water, keep fires from starting, and protect plants from drought. 

But digging a sprinkler system is not an easy job. If you don’t know how to dig right, you could hurt your property or make it flood. So, how do you dig a well for sprinkler system? Here are the steps to follow. 

Irrigation Wells

Irrigation Wells for watering crops are common in many farming areas. They are used to bring water from below ground to crops above ground. This is an important job for farmers because it helps them give plants the water and nutrients they need. If irrigation wells are not taken care of properly, they can get broken. 

Water won’t flow freely through the well if it gets clogged or if the seal between the well and the ground is broken. This can hurt the soil and plants around the well and cost a lot of money to fix or even replace the well. 

It is important to keep irrigation wells clean so that they work well and don’t hurt their surroundings or themselves. When the wellhead and the area around it are cleaned regularly, problems are less likely to happen. 

Different Types of Irrigation Wells 

There are many different types and sizes of irrigation wells. They are different in size, depth, and function. Some irrigation wells are used to water crops, while others are used to get drinking water. 

Open wells and closed wells are the two main types of irrigation wells. Most open wells are dug right into the ground and made of concrete. Most closed wells are made of steel and buried in the ground. 

Closed wells cost more to build and keep up than open wells. They are open to the weather, though, so they can get damaged easily. On the other hand, wells that are closed are safer from bad weather and easier to clean. 

Most of the time, closed wells are better than open ones. You should buy a closed well if you want to put in an irrigation system. 

How to Dig a Well for Sprinkler System

Step 1. Determine Where to Dig 

Find out where you want to put the sprinkler system before you start to dig. This step is very important because you can’t dig without permission. 

Before you dig, you must get a permit from the city. Make sure you check to see if you need a permit to dig where you want to. 

Step 2: Dig the area out

The first step in putting in a sprinkler system is to dig up the area. Before you start to dig, you should get ready for the job. 

Make sure you have what you need to do the job. You’ll need shovels, picks, rakes, and wheelbarrows, among other things. 

To set up a sprinkler system, it’s best to get help from a professional. But if you are sure you can do the job, you can dig out the area yourself. 

Step 3. Install Water Lines 

After you’re done digging, you should put in water lines. The sprinkler Wellhead cover is connected to the main valve box by water lines. 

There are different sizes of water pipes. Choose the size based on how far apart the valves are and where the sprinkler heads will be. 

Follow the manufacturer’s instructions to put the pipe in place. Make sure you don’t break or bend the pipe. 

Step 4. Connect Pipes Together 

When putting in a sprinkler system, it is also important to connect the pipes together. To connect the pipes, put one end of each pipe into the other end of the other pipe. To make the connection stronger, use pliers. 

Step 5. Place Valves 

Put the valves close to the floor. Each valve has its own part of the irrigation line that it controls. Valves can be either automatic or by hand. When the water gets to a certain level, automatic valves open on their own. Water flow can be controlled by hand with manual valves. 

Automatic valves are harder to work with than manual ones. But the price of automatic valves is less. 

Step 6. Fill Up the Boxes 

Put sand or gravel in the boxes. This helps soak up water and stop leaks. 

Step 7. Test the System 

Test the sprinkler system after installation. Test the sprinkler system by turning on the power supply. Once you’ve made sure everything works, turn off the power source. 

Step 8. Clean Up 

After the installation is done, clean the area well. Get rid of all the trash and dirt. Before cleaning, don’t forget to take off the sprinkler Wellhead cover


Putting in a sprinkler system takes skill and patience. Follow these tips to keep your property from getting broken or flooded.


Leave A Reply